E145S

Electronic control unit

Use application field

For swing-leaf or sliding-leaf gate automations 230V
  • The E145S electronic control unit can command one or two swinging door operators, a sliding gearmotor or mixed systems of swinging-sliding doors
  • It is compatible with all receivers (3-pin or 5-pin or external) and all photocells (both BUS and tradional ones)

For all product info download the PDF of our product catalogue.

Model

E145S

Power supply voltage

Power switching 90V~ a 260V~ 50(60) Hz

Max. power

4W Stand by, <2W with sleep function (programmable via PC/MAC) W

Motor max power

800 W

Max. accessories load

500 mA 24V – 500 mA BUS 2easy

Max. electric lock load

FAAC Lock (12V~ – 24V – 500 mA

Programming

LCD display and buttons, via Simply Connect connectivity devices

Status signalling

LCD Display and LED

Terminal board inputs

Open, Open pedestrian door, Stop (closed), BUS 2easy, Safeties in opening, Safeties in closing, Power supply + Ground, Opening and closing limit switches, Input for safety edge in opening, Input for safety edge in closing

Terminal board outputs

Flashing light, Motors, Accessories power 24V , 2 programmable OUTPUT (default:power indicator light and fails-safe), 2 electric locks

Rapid connector

XF 433/868 module for OmniDEC decoding, connector for DECODER/MINIDEC/RP, USB-A, Simply Connect

Protection Fuses

1 (10A)

Operating ambient temperature

-20°C ÷ +55°C

Note: The electronic board E145S can control one or more swing operators, a sliding gear motor, or a mixture of swing-sliding systems.

Basic programming

Type of motors

Selectable (swing, sliding, mixed swing – sliding installation)

Operating logic

Semiautomatic, Semiautomatic Step by Step, Safety Automatic, Automatic with reverse in pause, Automatic Step by Step, Safety Automatic Step by Step, Automatic, Automatic 1, Automatic with timer function, Semiautomatic B, Mixed (AP with pulse/CH with “dead-man”), deadman C,Custom (PC/MAC)

Pause time

Independently programmable after total or partial opening (from 0 to 9 min 50 sec)

Number of motors

Selectable

Thrust power

Adjustable on 50 levels for each motor independently

Encoder use

Selectable

Limit switch

limit switch function in opening and closing, selectable independently

Leaf delay time in closing

Programmable (from 0 to 1 min 30 sec)

BUS 2-Easy device registration

Selectable

Motor Power

1 and 2 (independently)

Working time learning

Simple self-learning (max 4 min and 10 sec).

Self-learning of working and deceleration time of the two leaves thanks to a single complete work cycle)

The SAFEcoder absolute encoder learns the open/closed/slowdown positions of the gate

Advanced programming

Maximum power at initial thrust

Selectable

Reverse stroke and ram stroke

Independently selectable (facilitating the coupling and uncoupling of the electric lock)

Leaf delay in opening

Selectable

Leaf 1 deceleration

Programmable, percentage of the total stroke (from 0% to 99%)

Leaf 2 deceleration

Programmable, percentage of the total stroke (from 0% to 99%)

Storable codes

Number of radio codes programmed on OMINIDEC through XF Module display

Pre-Flashing

Photocell in closing

Selectable Function

ADMAP Function

Selectable

Anti-crushing sensitivity

Programmable there is an ENCODER (10 levels)

Mechanical stop angle search

Selectable if the ENCODER is present

Additional work time

Selectable (if ENCODERS or limit switches are not present)

OUT 1 and OUT2 programming

Independently selectable (17 statuses each)

Service request

Selectable (if the programmed number of cycles is reached, the system activates an 8 sec pre-flashing before any movement)

Cycle count

Selectable (upgrade of a ”countdown” – max setting 99,000 cycles)

File management through USB-A

Board software Upgrade

Selectable

Board configuration Upload

Selectable

Toard configuration Upload

Selectable

Radio codes list Upload

Selectable

Board configuration download

Selectable

Board timer download

Selectable

Board radio code download

Selectable

Simply Connect

The Simply Connect quick connector allows the use of connectivity devices that permit remote programming and management via web and/or App of all the automations connected to the Simply Connect cloud platform: carry out diagnosis, investigate faults, perform remote maintenance and schedule your work

Enclosure mod. E for electronic control units

720119

||valuta|| ||720119||

Enclosure mod. L for electronic control units

720118

||valuta|| ||720118||

Enclosure mod. LM for electronic control units

720309

||valuta|| ||720309||

Release lock with key for mod. L and LM

712805

||valuta|| ||712805||